uhub/doc/uhub.conf

125 lines
4.5 KiB
Plaintext

# uhub.conf - A example configuration file.
# You should normally place this file in /etc/uhub/uhub.conf
# and customize some of the settings below.
#
# This file is read only to the uhub daemon, and if you
# make changes to it while uhub is running you can send a
# HUP signal to it ( $ killall -HUP uhub ), to reparse configuration (only on UNIX).
# All configuration directives: https://www.uhub.org/config.php
# Bind to this port and address
# server_bind_addr=any means listen to "::" if IPv6 is supported
# by the host OS, otherwise 0.0.0.0.
server_port=1511
server_bind_addr=any
# Alternative server ports
# server_alt_ports = 1512, 1513
# The maximum amount of users allowed on the hub.
max_users=500
# If 1, will show a "Powered by uHub/{VERSION}".
show_banner=1
# If enabled then operating system and cpu architecture is part of the banner.
show_banner_sys_info=1
# Allow only registered users on the hub if set to 1.
registered_users_only=0
# A server name and description.
hub_name=my hub
hub_description=Powered by uHub
# Set this to 0, and the hub will disconnect everyone
hub_enabled=1
# Access control list (user database)
file_acl=/etc/uhub/users.conf
# This file can contain a conf for plugin subsystem
file_plugins = /etc/uhub/plugins.conf
# Slots/share/hubs limits
limit_max_hubs_user = 0
limit_max_hubs_reg = 0
limit_max_hubs_op = 0
limit_max_hubs = 0
limit_min_hubs_user = 0
limit_min_hubs_reg = 0
limit_min_hubs_op = 0
limit_min_share = 0
# Example:
# To require users to share at least 1 GB in order to enter the hub:
# limit_min_share = 1024
limit_max_share = 0
limit_min_slots = 0
limit_max_slots = 0
# Flood control support:
# set the interval to 5 seconds
flood_ctl_interval = 5
# Then the maximum chat, connect, search, updates etc will be measured over 5 seconds.
# So, 3 chat messages per 5 seconds allowed.
flood_ctl_chat=3
flood_ctl_connect=20
flood_ctl_search=1
flood_ctl_update=2
flood_ctl_extras=5
# chat control
# if chat_is_privileged=yes only registered users may write in main chat
chat_is_privileged = no
# if obsolete_clients=1 allows old clients to enter , 0 gives an error message (msg_proto_obsolete_adc0) if they try connect
# defaults obsolete_clients=1
obsolete_clients=1
# Configure status message as sent to clients in different circumstances.
msg_hub_full = Hub is full
msg_hub_disabled = Hub is disabled
msg_hub_registered_users_only = Hub is for registered users only
msg_inf_error_nick_missing = No nickname given
msg_inf_error_nick_multiple = Multiple nicknames given
msg_inf_error_nick_invalid = Nickname is invalid
msg_inf_error_nick_long = Nickname too long
msg_inf_error_nick_short = Nickname too short
msg_inf_error_nick_spaces = Nickname cannot start with spaces
msg_inf_error_nick_bad_chars = Nickname contains invalid characters
msg_inf_error_nick_not_utf8 = Nickname is not valid utf8
msg_inf_error_nick_taken = Nickname is already in use
msg_inf_error_nick_restricted = Nickname cannot be used on this hub
msg_inf_error_cid_invalid = CID is not valid
msg_inf_error_cid_missing = CID is not specified
msg_inf_error_cid_taken = CID is taken
msg_inf_error_pid_missing = PID is not specified
msg_inf_error_pid_invalid = PID is invalid
msg_ban_permanently = Banned permanently
msg_ban_temporarily = Banned temporarily
msg_auth_invalid_password = Password is wrong
msg_auth_user_not_found = User not found in password database
msg_user_share_size_low = User is not sharing enough
msg_user_share_size_high = User is sharing too much
msg_user_slots_low = User has too few upload slots
msg_user_slots_high = User has too many upload slots
msg_user_hub_limit_low = User is on too few hubs
msg_user_hub_limit_high = User is on too many hubs
msg_error_no_memory = Out of memory
msg_user_flood_chat = Chat flood detected, messages are dropped.
msg_user_flood_connect = Connect flood detected, connection refused.
msg_user_flood_search = Search flood detected, search is stopped.
msg_user_flood_update = Update flood detected.
msg_user_flood_extras = Flood detected.
# If a client that supports ADC but not a compatible hash algorithm (tiger),
# then the hub cannot accept the client:
msg_proto_no_common_hash = No common hash algorithm.
# Message to be shown to old clients using an older version of ADC than ADC/1.0
msg_proto_obsolete_adc0 = Client is using an obsolete ADC protocol version.