uhub/doc/uhub.conf

109 lines
3.8 KiB
Plaintext
Raw Normal View History

2009-02-19 16:14:09 +00:00
# uhub.conf - A example configuration file.
# You should normally place this file in /etc/uhub/uhub.conf
# And change the file_acl and file_motd below.
#
# This file is read only to the uhub deamon, and if you
# make changes to it while uhub is running you can send a
# HUP signal to it ( $ killall -HUP uhub ), to reparse configuration (only on UNIX).
# All configuration directives: http://www.uhub.org/config.php
2009-02-19 16:14:09 +00:00
# Bind to this port and address
# server_bind_addr=any means listen to "::" if IPv6 is supported
# by the host OS, otherwise 0.0.0.0.
server_port=1511
server_bind_addr=any
# Alternative server ports
# server_alt_ports = 1512, 1513
2009-02-19 16:14:09 +00:00
# The maximum amount of users allowed on the hub.
max_users=500
# If 1, will show a "Powered by uHub/{VERSION}".
2009-02-19 16:14:09 +00:00
show_banner=1
# If enabled then operating system and cpu architecture is part of the banner.
show_banner_sys_info=1
2009-02-19 16:14:09 +00:00
# Allow only registered users on the hub if set to 1.
registered_users_only=0
# A server name and description.
hub_name=my hub
hub_description=Powered by uHub
# Set this to 0, and the hub will disconnect everyone
hub_enabled=1
# Access control list (user database)
file_acl=/etc/uhub/users.conf
# This file can contain a message of the day. A welcome
# message send to any client when connecting.
# If the file does not exist, is empty, or cannot be opened
# the motd will not be sent to the clients.
# Normally this message is sent to clients when connecting.
file_motd=/etc/uhub/motd.txt
# This file can contain a rules of the hub.
# Normally this message is sent to clients when write in chat !rules
file_rules=/etc/uhub/rules.txt
# Slots\share\hubs limits
limit_max_hubs_user = 0
limit_max_hubs_reg = 0
limit_max_hubs_op = 0
limit_max_hubs = 0
limit_min_hubs_user = 0
limit_min_hubs_reg = 0
limit_min_hubs_op = 0
limit_min_share = 0
# Example:
# To require users to share at least 1 GB in order to enter the hub:
# limit_min_share = 1024
limit_max_share = 0
limit_min_slots = 0
limit_max_slots = 0
2010-02-02 10:43:10 +00:00
# chat control
# if chat_is_privileged=yes only registered users may write in main chat
chat_is_privileged = no
2010-02-02 10:43:10 +00:00
# if chat_only = yes then search and transfer functionality is disabled for
# non-operator users.
chat_only = no
2009-02-19 16:14:09 +00:00
# Configure status message as sent to clients in different circumstances.
msg_hub_full = Hub is full
msg_hub_disabled = Hub is disabled
msg_hub_registered_users_only = Hub is for registered users only
msg_inf_error_nick_missing = No nickname given
msg_inf_error_nick_multiple = Multiple nicknames given
msg_inf_error_nick_invalid = Nickname is invalid
msg_inf_error_nick_long = Nickname too long
msg_inf_error_nick_short = Nickname too short
msg_inf_error_nick_spaces = Nickname cannot start with spaces
msg_inf_error_nick_bad_chars = Nickname contains invalid characters
msg_inf_error_nick_not_utf8 = Nickname is not valid utf8
msg_inf_error_nick_taken = Nickname is already in use
msg_inf_error_nick_restricted = Nickname cannot be used on this hub
msg_inf_error_cid_invalid = CID is not valid
msg_inf_error_cid_missing = CID is not specified
msg_inf_error_cid_taken = CID is taken
msg_inf_error_pid_missing = PID is not specified
msg_inf_error_pid_invalid = PID is invalid
msg_ban_permanently = Banned permanently
msg_ban_temporarily = Banned temporarily
msg_auth_invalid_password = Password is wrong
msg_auth_user_not_found = User not found in password database
msg_user_share_size_low = User is not sharing enough
msg_user_share_size_high = User is sharing too much
msg_user_slots_low = User have too few upload slots
msg_user_slots_high = User have too many upload slots
msg_user_hub_limit_low = User is on too few hubs
msg_user_hub_limit_high = User is on too many hubs
2009-02-19 16:14:09 +00:00
msg_error_no_memory = No memory